"ALL NEW"
'06-'07 YZF R6:
New Parts / Updated: 7-7-2010
We update these pages often.
Be sure to hit REFRESH on your browser, each time you check this page.
Or it may Not Show the new parts.
'06-'07 Graves Factory Yamaha R6 FX Bike
Only the Best Parts on the Planet go on these
bikes
(Akrapovic Evolution Exhaust w/ Ti Can., Ohlins Superbike Forks, Ohlins
TTX
Shock, Marchesini Forged Magnesium Rims,)
((Dyno Jet Power Commander IIIusb, Dyno Jet
Ignition Module, Dyno Jet
Quick Shifter, DID Chain,
AFAM Sprockets)
(STM Slipper Clutch, SharkSkinz Bodywork, Galfer Wave Rotors,
and a few more parts, no one knows about.) Every part listed here is the SAME EXACT Part, you can
put on your own bike. And we can get it for you.
AVAILABLE NOW
The All New PCIIIusb & Dyno Jet Quick
Shifters:
Featuring: State of the Art Technology
New Mapping methods, USB Port For Easier & Faster
Transfer and Auxiliary Data Port for Future Add-ons.
Get One Now, Before they are all on Back Order.
PCIIIusb ON SALE - $265
IN STOCK
For More Details: & Buy
It Now >> DynoJet Power
Commanders PCIIIusb <<
The Dynojet Quick Shifter Sensors are compatible with USB Power
Commander ONLY and allow "full throttle, clutch-
less" upshifts. These high quality sensors provide fast, accurate and
reliable shifting in conjunction with the Power Commander. Sensors are
attached to the gear linkage and connect into the Power Commander expansion
port. All sensors include a Software utility which allows the user to adjust
the "Kill Time" and "Minimum RPM Shift Point" within the Power Commander
Control Center Software. "Please note these are
NOT Power Shifters. They do
NOT shift for you. They
allow "full throttle, clutch- less" upshifts, by cutting the Fuel
or Spark for a split second as you start to shift
with your foot..
Dyno Jet Quick Shifters:
ON SALE - $197 (IN
STOCK)
Buy It Now >>
DynoJet
Quick Shifters <<Requires Ignition Module
For more information,
please refer to the guide belo: Linkage Adapters ONLY Sold w/ Quick Shifters.(Not sold Separately)
Linear Sensors are universal..
Shift Rod Sensors require the gear linkage tie-rod to be modified. We are developing a
range of tie-rods for the popular models, as well as universal tie-rods that are
specifically designed to give maximum adjustment, allowing a combination of different M6
right hand and left hand male and female threads over a wide range of 160mm to 280mm. This
will allow easy installation on many models as well as some custom rear-set applications..
<-click
CBR1000RR Dyno Map, showing nearly 4 HP Gain, everywhere, With JUST the Ign.
Module changes.
Some bike have shown gains over 8 hp, in certain areas, by simply changing
the Ignition Timing.
Power Commander Ignition Module
An “Add-On”
Power Commander Ignition Module
for Power Commander USB’s,
are available NOW. These modules will plug directly into the PCIIIUSB’s expansion port and the
bike’s ignition coils. Dynojet
Ignition Modules
use the latest in “direct coil driver technology.” Both advancing and
retarding of the ignition timing at specific throttle postion and rpm combination will be
possible. In “Advanced Mode,” the tuner will be able to set the timing for each
cylinder individually.
When tuned correctly, the Ignition module has potential to make excellent HP
Gains Through out the RPM Range. The Ignition Module will Also
allow the User to increase his Rev. Limiter of the Bike, Enabling them to
Tap the Most power
possible from the engine.
(Note, this does require a signed waiver form) The
Power Commander Ignition
Module will be
available for popular sport bike models.
This does not apply to Harley Davidson model Power Commander USB’s, as they include
ignition timing adjustment ability as part of the base unit..
The Dynojet Ignition Module is an “add on” accessory for
select Power Commander III USB. It allows you to control and adjust the
ignition timing of your motorcycles’ engine.
The Dynojet Ignition Module is connected to the PCIII USB with it’s built in
expansion port link and communicates via a CAN interface. As in the case of
the Power Commander, the Dynojet Ignition Module uses OEM style connectors
to plug in-line of the stock ignition harness so no cutting or splicing is
required.
The Dynojet Ignition Module uses “direct coil driver technology” and allows
a high degree of timing adjustment. In the Power commander Control Center
Software the user is able to advance or retard the ignition curve up to 10
degrees based on throttle position and RPM. It is also possible to alter the
timing for each cylinder individually if necessary.
The Ignition Module comes standard
with no adjustments made in the map for the timing table. Due to different
states of tune, fuel quality, and engine modifications we found it is best
to leave the ignition timing stock for safety reasons.
On motorcycles that have eight injectors and were not previously able to
benefit from the use of the Dynojet Quick Shifter, the Ignition Module now
allows this functionality. The Dynojet Quick Shifter is connected to the
expansion port between the Ignition Module and the PCIIIusb. Regular Price - $361
ON SALE - $285 Buy it Now >>
DynoJet
Ignition Modules <<
BREMBO RSC Yamaha Replacement Cable Clutch Lever Mechanical clutch lever assembly machined entirely from billet.
Lever boss has special geometry. Plug-and-play design ensures the lever can
mount directly to the original arm lever assembly. Similar in all respects to
the 19RCS Master Cylinder with laser-imprinted Brembo® Racing logo and the
famous tri-color flag on the lever boss.
Perfect Match for your RCS19 Brake RSC Yamaha Cable Clutch Lever
Sale Price:
$149.95 Fits These Model Bikes ONLY: '02-'10 R1, & '99-'10 R6
<<--Click TRUE HIGH INTENSITY DISCHARGE (H.I.D.) LIGHTS
XENON LIGHTS .. KITS Starting at Only - $74.95/each >> HID LIGHT
CONVERSION KITS <<
TruGel Batteries The Ultimate LONG Lasting Top Quality
Motorcycle Battery. PERIOD.
And Best of All, They are LESS Cost then traditional Lead/acid batteries
The newest offering from the Brembo HP line. The M4 CAST Monobloc Caliper.
Designed with an entry level cost in mind... Using
CAST Alum.
Instead of Billet.
These calipers are of monoblock construction utilizing a unique gravity cast
procedure.
High temperature main seals plus dust seals allow for use on street or on
the track.
Caliper CAST ALUM. bodies are then CNC machined.
Brake pads made from sintered material so & are ideal for use in wet and dry
conditions.
Kit includes instruction manual with all information about fitting,
bleeding, maintenance and more. 108mm
M4 Cast Alum. Calipers
Retail - $1098(Except 07-08 R1)
Price Includes Brembo PADS.
Sale Price - $988/set
of 2 Calipers
To See More Information on BREMBO CALIPERS, ROTORS and MASTERCYLINDERS
>> BREMBO<<
Hotbodies Color Matched Rear Huggers, and
VENTED Front Fenders >>
HOTBODIES
<<
GPR Steering Damper
NO
Drilling required
>>
GPR
Steering Damper <<
Retail - $505
Sale Price - $379
CURRENTLY VERY LIMITED
QTY.
IN STOCK
BLACK or Ti/Gunmetal
Clear Tail Lights
w/ Optional Integrated LED Signals
(CTL-0095) Only - $99.95IN
STOCK
>> Clear
Tail Lights & LED's <<
Unlike our Competitors, who sell Just a Circuit Board,
and require you to tear appart your entire Tail Light.....
We sell only the COMPLETETail Light Housing.
Just pop out your stock Tail Light, and Insert this one. OEM Plug for Tail Light. NOTE: (TAIL Light come with Turn
signal option.
You don't Have to use them, if you don't want to. But, they are included in
the price.)
Akrapovic Slip-ons, Race and Evolution Systems.
Carbon or Titanium HEX
- IN
STOCK
VERY LIMITED QUANTITY
Akrapovic
Exhausts
Hotbodies ABS Undertail w/ Built in LED Signal Lights
Built for speed, this new SBK undertail gives your
bike a modern, aggressive MotoGP shape! Produced in ABS plastic,
it has an OEM fit and finish, same as the stock undertail.This undertail has a new license plate light to keep it legal
on the streets. Requiring barely any modifications, this SBK undertail
has a flawless color match and is very easy to install.
Gloss Black - 06-07' Undertail
Blue - 06-07' Undertail
Dark Bluish Grey - 06-07' Undertail
Red - 07' Undertail
Yellow - 06' Undertail
SALE PRICE - $179.95
- HOTBODIES COLOR
MATCHED UNDERTAILS and HUGGERS -
Run ALL NEW Drag Race
Simulator for Dyno Jet LCD Screen
-
-DYNO JET
LCD DISPLAY
-
- DYNO JET Mult-Function
Hub -
Want To SEE What your bike, and
Power Commander are Doing WITHOUT A COMPUTER.
Do you Want to Switch MAPS on the Fly, or see what gear you are in, or See
what your fuel load is?
Do you want to tweak your map away from your house. Then you want a
Dyno Jet LCD Display.
UNIT
Plugs Directly into Your Power Commander IIIusb. Allows you to
View Maps, Current Speed, Gear Position, RPM, TPS and Much More
Can also Mtn. ON BIKE, in place of Gauges
(On some Bikes)
Click here for More Details
>> LCD DISPLAY
<<
LTD. QTY. IN STOCK
Starlane GPS Lap Timer
w/
Speedometer and RPM Pickup
>> Starlane GPS Lap Timers
<< GPS (Satellite) Technology.
NO Transponder Need. Imagine, No More worrying about setup .Transponders on the
side of the track each time you go out, or
Each time you come in. Those days are done.
Just go out on the track, Set the Start/Finish Line and the GPS (Satellites) Does it all for you. Current Speed, Lap Times, RPM;s, Max Speed, Fastest lap.....and
much more.
You can even Save each track, in memory. NO Wire Splicing, or
taping necessary.
This Unit
Easily transfers from bike to bike. Or you can put it in your car, or
truck, or SUV.
Very handy device.
TYPE R - With TRACK MAPPING. Downloaded to your
PC or Laptop
'06-'07 R6 BMC Filters Street or Race Filter :
Air Flow Funnel Included (as
Shown) TRACK Filter Air Flow Funnel Not
Included, Only for Track Use BMC High
Flow Air Filters 9-5-06 VERY Limited QTY.
IN Stock
STM Slipper Clutches IN STOCK
Slipper Clutches are now becoming Standard equipment
on more and more
NEW Sport Bikes such as (05-06 GSX-R1000 / 04-06 ZX-10R / 03-06
ZX636/6RR, .
Now, STM Has released a Model for nearly ALL Popular Models
STM Slipper Clutches are an excellent Upgrade to High Performance Sport
Bikes.
PIG Spotter Mirrors w/ LED Turn Signals These are the Ultimate Mirrors made from Billet Aluminum with
Convex Lens Offered in: Black / Polished / Chrome
> PIG Spotters <
CRG Levers are Carved from aluminum.
They are beautiful
as well as functional.
CRG Levers are Designed to be bolt on replacements, fully adjustable.
Available in Gold or Gray.
A few Select CRG Levers are available in a short lever version. (
1.25" Shorter ) Learn More or Buy Now >
CRG Levers <
- $84.95
& Up IN STOCK
ALL NEW
Brembo "HP" BILLET Brake Calipers
(2 Piece Design) 4
Piston, 2 Pad Setup.
Designed very similar to
the "Racing" Monobloc Calipers.
But, at LESS then half the Cost.
EXCELLENT Upgrade and OEM Fit.
108mm Bolt-Hole Setup
for Most Japanese Sport Bikes, That have Radial Calipers Stock.
Brembo has developed a new caliper with radial attachments that is
interchangeable on the standard radial forks of maxisport class Japanese
machines (HONDA, YAMAHA, SUZUKI, KAWASAKI). With a caliper body machined
from solid metal, special attention was paid to achieving high braking power
and stiffness, utilizing technology derived
directly from race engineering. The product, which is supplied in kit form,
is equipped with sintered brake pads - at the cutting edge of today's
manufacturing technology; the kit also contains an instruction handbook, a
set of Brembo decals, and a series of practical temperature stickers as used
in race conditions to monitor the working temperature of the calipers. The
stickers clearly identify the thoroughbred race pedigree of the brakes.
To assure that we send you the correct spacers, please let us know the make,
model and year of the bike that you plan on putting these calipers on.
Retail - $850.95
Sale Price - <
BREMBO PRICING >
Price Includes Brembo PADS.
The
floating rotors were developed specifically to provide owners of
Japanese Sportbikes (HONDA, YAMAHA, SUZUKI, KAWASAKI) with the
maximum performance levels on the street and on the track. The
new rotors are available in three diameters and are of greater
thickness than standard rotors. The braking surface features a
series of drilled holes to maximize performance and control when
braking while simultaneously reducing rotating mass with
consequent advantages in terms of machine handling. The braking
surface is connected to the carrier, which is machined from
solid aluminum and is the product of a comprehensive FEM
calculation procedure. The connection is achieved by means of
ten floating- type aluminum buttons, reflecting a strictly race
style engineering project. The kit contains the two rotors, and
a set of Brembo decals.
Retail - $669.95 Sale Price - <
BREMBO PRICING >
Clear Tail Lights
w/ Optional Integrated LED Signals
(CTL-0095) Only - $99.95IN
STOCK
>> Clear
Tail Lights & LED's <<
Unlike our Competitors, who sell Just a Circuit Board,
and require you to tear appart your entire Tail Light.....
We sell only the COMPLETETail Light Housing.
Just pop out your stock Tail Light, and Insert this one. OEM Plug for Tail Light. NOTE: (TAIL Light come with Turn
signal option.
You don't Have to use them, if you don't want to. But, they are included in
the price.)
STM Slipper Clutches IN STOCK
Slipper Clutches are now becoming Standard equipment
on more and more
NEW Sport Bikes such as (05-06 GSX-R1000 / 04-06 ZX-10R / 03-06
ZX636/6RR, 06 R6).
Now, STM Has released a Model for nearly ALL Popular Models
STM Slipper Clutches are an excellent Upgrade to High Performance Sport
Bikes.
Ti-Force FULL TITANIUM SYSTEM Ti-Force FULL TITANIUM SYSTEM
Full Ti Systems (Shorty
Canister w/ Conical End) Retail
$1379
SALE PRICE - $1149
IN STOCK
Full Ti System weighs only 6 pounds(Compared
to 20.5 lbs for stock exhaust)
Ti
Slip-ons (Short Canister w/ Conical
End) Retail $697
- SALE PRICE - $379 IN STOCK
Ti Slip-on weighs only 2.2 pounds
Hyper Pro
Active Damper - $519 ON SALE - $449 IN STOCK Unfortunately, No Pictures on the Bike Yet. Coming
Soon.
GPR Steering Damper
NO
Drilling required
>>
GPR
Steering Damper <<
Retail - $505
Sale Price - $379
CURRENTLY VERY LIMITED
QTY.
IN STOCK
BLACK or Ti/Gunmetal
Micron Stainless & Colored BLACK or GRAY "Moto GP Mega-Phone" Slip-ons Micron Slip-OnsIN STOCK
Micron Serpent Full System
See Dyno Graph >> Micron SerpentsIN STOCK
Micron is
proud to announce the awesome 6th Generation Serpent design is now in stock
and available for the 2006 Yamaha R6. Specifically designed for the all new
"Moto GP" look, Micron takes hydroforming to the next level with not only a
fully hydroformed header ( 8.5 lbs of
engineering excellence!), but the incredible Serpent GP muffler is
also fully hydroformed to match the sculptured design of the new Yamaha.
This kit
is The equivalant of a Set of Ohlins Forks,
Less the Sliders, and Bottoms.
Everything INSIDE a Set of Ohlins RT Forks, comes in this Kit.
• Includes Complete Internal Cartridge
NEW Compression Pistons, NEW Rebound Pistons NEW Piston Rings NEW Shims Complete Set of One-Way Valves, NEW Washers
NEW 25mm Fork Springs
Recommended Track Settings
External rebound Damping External compression Damping External Spring preload adjusters
Same 25mm Fork Springs that
are on the R&T Forks Works with STOCK Fork sliders and bottoms, so it's
SuperSport Legal
In nearly all regions.
'06-'07 R6 Fender
Eliminator Kit 1Y607 - $135.95 $109
Includes Solid Mtn. Tag Bracket,
and New Turn Signals.
Retains Stock Tag Light
(Exactly As Shown)
>> SharkSkinz Racing Bodywork
<<
"Call or E-Mail For Package Prices" (Belly pan requires
removal of Stock catalytic Converter
and replaced wth Aftermarket Exhaust)
CRG Levers are Carved from aluminum.
They are beautiful
as well as functional.
CRG Levers are Designed to be bolt on replacements, fully adjustable.
Available in Gold or Gray.
A few Select CRG Levers are available in a short lever version. (
1.25" Shorter ) Learn More or Buy Now >
CRG Levers <
- $89.95
& Up
The
floating rotors were developed specifically to provide owners of
Japanese Sportbikes (HONDA, YAMAHA, SUZUKI, KAWASAKI) with the
maximum performance levels on the street and on the track. The
new rotors are available in three diameters and are of greater
thickness than standard rotors. The braking surface features a
series of drilled holes to maximize performance and control when
braking while simultaneously reducing rotating mass with
consequent advantages in terms of machine handling. The braking
surface is connected to the carrier, which is machined from
solid aluminum and is the product of a comprehensive FEM
calculation procedure. The connection is achieved by means of
ten floating- type aluminum buttons, reflecting a strictly race
style engineering project. The kit contains the two rotors, and
a set of Brembo decals.
$109
